» Empty the pool, use a soft brush, mild detergent and water to remove algae stains from the pool liner. Thoroughly rinse and dry before refilling or storage.
» Water condition varies from country to country, states, region, and within specific zones and areas. In some regions the water could be "hard water", this is because the water contains excessive minerals, such as calcium and magnesium, thus causing the water to adopt a milky color. Check your local pool supply store for advice on water treatment and balance.
» Your pool can be easily emptied and stored in a safe place during the winter. However, many people choose to leave their pool up year round. In areas where freezing temperatures occur, there is risk of ice damage. It is recommended to drain, disassemble and store the pool in a safe place when temperatures drop below 32 degrees Fahrenheit. See "How To Drain Your Pool" section.
Clean pool water thoroughly (If Easy Set Pool make sure the top ring is properly inflated).
Remove the skimmer (if applicable) or any accessories attached to the threaded strainer connector. Replace strainer grid if necessary. Be sure all accessories parts are clean and completely dry before storage.
Plug the Inlet and Outlet fitting from the inside of the pool with the plug provided (sizes 10' and 12'). Close the Inlet and Outlet Plunger Valve (15', 18', and 24').
Remove the ladder (if applicable) and store in a safe place. Be sure the ladder is completely dry before storage.
Remove the hoses that connect the pump and filter to the pool.
Add appropriate winter chemicals. Consult your local pool dealer as different regions vary greatly.
Cover pool with Intex Pool Cover. IMPORTANT: INTEX POOL COVER IS NOT A SAFETY COVER.
Clean and drain pump, filter housing and hoses. Remove and discard old filter cartridge (keep a spare cartridge available for next season).
Bring pump and filter parts indoors and store in a safe and dry area, preferably heated.
STORING POOL FOR WINTER
After draining pool, dry pool liner completely (100%). Sprinkle talcum powder on liner to prevent vinyl from sticking together and to absorb any water you may have missed.
Roll pool liner to avoid creases and relocate to storage area. Place it in original carton if you saved it.
Keep all small parts together with filter pump, manual, and pool, and then place in an area that will remain at room temperature throughout the storage season.
» Excessive use of pool chemicals can cause the color of the inside wall printing to fade away faster, like a heavy chlorinated public swimming will cause a bathing suit color to fade
» Yes, in some cases certain types of hardy grass such as Bermuda or St. Augustine can grow through the liner. Before setting up your pool, it is recommended that you clear the area of these types of hardy grasses. INTEX will not be held responsible for grasses that may grow through the ground cloth and / or pool liner, as this is not a manufacturing defect. A ground cloth or tarp may be helpful in preventing this from occurring.
» The diameter of the Solar Cover perfectly matches round metal frame pools, due to the shape of the Easy Set pool; you need to fold the edge of the Solar Cover under the top ring.
» A PVC or silicon based glue for repairing camping mats, tents, shoes, inflatable boats, etc are suitable for INTEX pools.
» The set of small holes on the center of the solar cover are for safety (same concept as the regular pool cover). In addition to that, there are also small holes equally spaced around the perimeter of the solar cover near the edge. Sometimes you may find the holes are not consistent, that’ll not affect the efficiency and life of your solar cover.
» Processing time is approximately 3 business days from the date we receive the product. It is then shipped by Fed EX Ground from Long Beach CA. Therefore, transit time will be determined by your location. (for U.S & Canada only)
» Yes. We distribute 10’(305cm) 12’(366cm) 15’(457cm) 18’(549cm) for both Easy Set and round metal frame pools, 9’x18’ (274x549cm) for rectangular frame pool.
» 90% of a swimming pool’s heat is lost through the water surface; use of Solar Cover will greatly reduce the heat lost. It will prolong your swimming season.
» If your e-mail address was provided at the time the order was placed, and your order was shipped by Fed EX, you will receive an e-mail confirmation with the tracking number. You can then go to the Fed EX website to track the package.
» Orders are shipped within 2-3 business days once the order is placed. Orders will be shipped by regular mail or Fed EX (depending on the size of the order). Therefore, transit time will be determined based on your location and shipping method.
» We distribute 10'(305cm) 12'(366cm) 15'(457cm) 18'(549cm) for both Easy Set and round metal frame pools, 9'x18' (274x549cm) for rectangular frame pool.
» Yes. Intex will accept replacement part orders, accessory orders, and warranty questions from Canadian consumers. For replacements on items other than Above Ground Pools and specific airbeds, please refer back to the original place of purchase. To order replacement parts please call 800-234-6839 or go to www.intexcorp.com.
» A 10’ (305cm) solar cover will FIT a 10’ INTEX metal frame pool or Easy Set pool, it doesn’t mean the diameter of the solar cover is 10’ (305cm), this rule also applies to all sizes of the INTEX solar cover.
» The bubble side.
» No. Our system does not accept COD (Cash on delivery) or check. We only accept Visa, Mastercard, American Express and Discover credit cards. Pre-paid credit cards can be used if they are from one of these four companies.(for U.S & Canada only)
» No.
