» Empty the pool, use a soft brush, mild detergent and water to remove algae stains from the pool liner. Thoroughly rinse and dry before refilling or storage.
» Water condition varies from country to country, states, region, and within specific zones and areas. In some regions the water could be "hard water", this is because the water contains excessive minerals, such as calcium and magnesium, thus causing the water to adopt a milky color. Check your local pool supply store for advice on water treatment and balance.
» Your pool can be easily emptied and stored in a safe place during the winter. However, many people choose to leave their pool up year round. In areas where freezing temperatures occur, there is risk of ice damage. It is recommended to drain, disassemble and store the pool in a safe place when temperatures drop below 32 degrees Fahrenheit. See "How To Drain Your Pool" section.
Clean pool water thoroughly (If Easy Set Pool make sure the top ring is properly inflated).
Remove the skimmer (if applicable) or any accessories attached to the threaded strainer connector. Replace strainer grid if necessary. Be sure all accessories parts are clean and completely dry before storage.
Plug the Inlet and Outlet fitting from the inside of the pool with the plug provided (sizes 10' and 12'). Close the Inlet and Outlet Plunger Valve (15', 18', and 24').
Remove the ladder (if applicable) and store in a safe place. Be sure the ladder is completely dry before storage.
Remove the hoses that connect the pump and filter to the pool.
Add appropriate winter chemicals. Consult your local pool dealer as different regions vary greatly.
Cover pool with Intex Pool Cover. IMPORTANT: INTEX POOL COVER IS NOT A SAFETY COVER.
Clean and drain pump, filter housing and hoses. Remove and discard old filter cartridge (keep a spare cartridge available for next season).
Bring pump and filter parts indoors and store in a safe and dry area, preferably heated.
STORING POOL FOR WINTER
After draining pool, dry pool liner completely (100%). Sprinkle talcum powder on liner to prevent vinyl from sticking together and to absorb any water you may have missed.
Roll pool liner to avoid creases and relocate to storage area. Place it in original carton if you saved it.
Keep all small parts together with filter pump, manual, and pool, and then place in an area that will remain at room temperature throughout the storage season.
» Excessive use of pool chemicals can cause the color of the inside wall printing to fade away faster, like a heavy chlorinated public swimming will cause a bathing suit color to fade
» Yes, in some cases certain types of hardy grass such as Bermuda or St. Augustine can grow through the liner. Before setting up your pool, it is recommended that you clear the area of these types of hardy grasses. INTEX will not be held responsible for grasses that may grow through the ground cloth and / or pool liner, as this is not a manufacturing defect. A ground cloth or tarp may be helpful in preventing this from occurring.
» A PVC or silicon based glue for repairing camping mats, tents, shoes, inflatable boats, etc are suitable for INTEX pools.
» Processing time is approximately 3 business days from the date we receive the product. It is then shipped by Fed EX Ground from Long Beach CA. Therefore, transit time will be determined by your location. (for U.S & Canada only)
» The restrainer strap must be installed with the welding seam facing downward (facing to the ground). Incorrect installation of the strainer strap may cause the strap to break and even pool collapsing.
» If your e-mail address was provided at the time the order was placed, and your order was shipped by Fed EX, you will receive an e-mail confirmation with the tracking number. You can then go to the Fed EX website to track the package.
» We distribute the sizes as attachment:
Note: All figures are approximate.
» Do not over inflate or use high-pressure air compressors. Inflate top ring to be slightly firm to the touch. An over-inflated ring heated by the sun may burst or lead to leaks in the seam. Pay attention to air temperature variation! In cold weather the top ring will lose some pressure, air will contract. If this occurs, DO NOT add air since the air inside will expand again once the temperature RISES. In hot weather, the air will expand. You MUST let some air out to prevent the top ring from failing due to excess internal pressure.
» Orders are shipped within 2-3 business days once the order is placed. Orders will be shipped by regular mail or Fed EX (depending on the size of the order). Therefore, transit time will be determined based on your location and shipping method.
» When a top ring is inflated during a hot and sunny day, the air inside will contract (less pressure) when the ambient temperature drops during the evening or early morning, thus giving a false impression the top ring keeps deflating. Do not over-inflate the top ring, and make sure the air valve is firmly secure and inserted.
» To the bottom of the inflated ring. Do Not Overfill, as this may cause the pool walls to become unstable and possibly result in injury or property damage from the water flowing over the pool wall while in use.
» Yes. Intex will accept replacement part orders, accessory orders, and warranty questions from Canadian consumers. For replacements on items other than Above Ground Pools and specific airbeds, please refer back to the original place of purchase. To order replacement parts please call 800-234-6839 or go to www.intexcorp.com.
» No. Our system does not accept COD (Cash on delivery) or check. We only accept Visa, Mastercard, American Express and Discover credit cards. Pre-paid credit cards can be used if they are from one of these four companies.(for U.S & Canada only)
» No.
